|
Product Details:
Payment & Shipping Terms:
|
| No. Of Heating Zones: | Top 8 & Bottom 8 | Length Of Heating Zones: | 2950 MM |
|---|---|---|---|
| Normal Operation Power: | About 9KW | No. Of Cooling Zones: | 2 |
| Mesh Width: | 450 MM | Dimension: | 5000*1300*1450 ( L*W*H ) |
| Product Name: | Reflow Oven 8 Zones Machine | Feature: | Lead Free Reflow Oven |
| High Light: | 9KW Reflow Oven Equipment,450mm Mesh Reflow Oven Equipment,Lead Free Reflow Oven PLC |
||
RF 800I Lead Free 8 Zone Reflow Oven
8 Heating Zones Reflow Oven Equipment for SMT Assembly Line
The Specification of Reflow Oven RF-800I
| Model | RF-800I |
| Temperature Deviation on PCB | ± 1.5C |
| Power Supply | 380V 50HZ / 220V 60HZ |
| Convryor Speed | 20-2000MM/min |
| Temp. Setting Range | Rome Temperature ~320C |
| No. of Heating Zones | Top 8 & Bottom 8 |
| Temperature Control Precision | ± 1C |
| Length of Heating Zones | 2950 MM |
| Normal Operation Power | About 9KW |
| PCB Conveyor Method | Mesh and Rails |
| No. of Cooling Zones | 2 |
| Max. Width of PCB | 50 ~ 400 MM |
| Nozzle Plate | Stainless Steel Plate |
| Mesh Width | 450 MM |
| Dimension ( L*W*H ) | 5000*1300*1450 |
The principle of reflow soldering is divided into several descriptions
A. When the PCB enters the heating zone, the solvent and gas in the solder paste evaporate, and at the same time, the flux in the solder paste wets the pads, component ends and pins, and the solder paste softens, collapses, and covers the solder The pads isolate the pads and component pins from oxygen.
B. When the PCB enters the heat preservation zone, the PCB and components are fully preheated to prevent the PCB from suddenly entering the welding high temperature zone and damaging the PCB and components.
C. When the PCB enters the soldering area, the temperature rises rapidly to make the solder paste reach a molten state, and the liquid solder wets, diffuses, diffuses, or reflows to the PCB pads, component ends and pins to form solder joints.
D. The PCB enters the cooling zone and the solder joints are solidified; when the reflow soldering is completed.
Other Information of Reflow Oven
01. High temperature
The machine is easy to malfunction in the high temperature environment, thus affects the production. Manufacturers do not know the cause of thecase that is mechanical damage, only normal use, attention to maintenance and micro-repair, these mechanical failure control.
02. Voltage problem of Reflow Oven
After-sales service manufacturers often encounter customer response tomechanical failure, such as mechanical heating can not work, unable torotate control display instability.
The causes of the above failures, in addition to a few poor quality, most of the voltage is not enough, capacityis not enough, line aging and lead to imbalance between circuits. If it isnot repaired in time, the machine will burn out.
03. Professional maintenance of Reflow Oven
Equipment professional electrical maintenance personnel, regular maintenance and repair of machinery.
Can also be under the guidanceof manufacturers to do a good job in the daily maintenance and regularmaintenance of machinery.
Picture Showing of Reflow Oven
RFQ About Reflow Oven
We have power limited in factory, how we can use your reflow oven, and avoid over-load trip when start up the machine ?
According to actual situation, we can make changes on machine software, and when start up the machine, the heating zones will be heated on one by one, it means the start up power is very low, so it will be no problem; also the customer can operate the reflow oven by manual mode, it’s very easy to set all parameters in the software.
Contact Person: Ivan Zhu
Tel: 86-13534290911
